BEE MORTAR

Tile Adhesive Mortar # 300 A is suitable for laying mosaic and ceramic tiles.

Quick-Repair Dry Concrete # 460-QR is suitable for repairing concrete works, especially where you need high early strength within 6 hours, e.g. road repairing works, concrete floors, etc.

DRY CONCRETE NO.400 - ES is suitable for a variety of concrete works,especially where you need high early strength within 24 hours, e.g. street repairing works etc.

DRY CONCRETE NO.400 - HP is suitable for a variety of concrete works, especially where you need high strength and workability, e.g.floors, streets, columns,and beams etc.

Dry Premixed Concrete # 400 is suitable for a variety of concrete works, e.g. general floors, walls, masonry beams, etc.

Dry Premixed Concrete # 400-GP is suitable for a variety of concrete works, e.g. general floors, walls, masonry beams, etc.

SC 100-TD consists of accurately weighed Portland cement, aggregates and chemical admixtures. The product is designed to be used as original or repair shotcrete in situations requiring a high-quality concrete with a choice of maximum aggregate size of 5mm. It may be mixed to any consistency from semi dry to plastic.

Padding Mortar Designed for use in setting the machine base level before grouting and for adjusting the prefabricated base (PRECAST).

High Strength Topping Mortar No.236 /236 S consists of accurately weighed Portland cement, fine aggregate and admixtures. The mortar will have high strength and little or no plastic shrinkage. An air-entraining agent is included in this product to give improved resistance to freezing and thawing. Typical uses include horizontal roads applications to parking floor,road surface, factory floor. High Strength Topping Mortar is non-toxic and contains no chloride that is harmful to reinforced steel.

High Strength Levelling Floor Screed No.235 consists of accurately weighed Portland cement, fine aggregate, silica fume and admixtures. The motar will have high strength and little or no plastic shrinkage. An air-entraining agent is included in this product to give improved resistance to freezing and thawing. Typical uses include horizontal roads applications to parking floor, road surface, factory floor. High Strength Levelling Floor Screed No. 235 is non-toxic and contains no chloride or gypsum that is harmful to reinforced steel. No.235 is semi-self leveling while No.235 S No.235S is Option High Compressive, Beeding.

High Strength Levelling Floor Screed No.234 SF consists of accurately weighed Portland cement, fine aggregate, admixtures. The motar will have high strength and little or no plastic shrinkage. An air-entraining agent is included in this product to give improved resistance to freezing and thawing. Typical uses include horizontal Slab applications to parking floor, road surface, factory floor. non-toxic and contains nochloride or gypsum that is harmful to reinforced steel.

Topping Mortar # 220 is suitable for repair work, leveling floors, paths, steps or others which need a smooth and durable surface texture with excellent adhesion properties.

To repair honeycombing, rock pockets, chips, spalls and accidental damage in concrete structures. To plug from tie holes and service conduit holes in concrete and masonry.To dry pack under base plates, columns and sole plates and for underpinning of walls.

Thin Coat Repair Mortar No.134 / 134 F consists of accurately weighed Portland cement, fine aggregate, silica fume and admixtures. Typical uses include vertical applications to bridges, piers, beams, tunnels, parking structures, water tanks and sewage treatment facilities, pulp and paper process areas, petrochemical process areas, dams and marine structures. Repair Mortar No.134 is non-toxic and contains no chloride that is harmful to reinforced steel.

Skim Coat Mortar No. 124 / 124 L is a polymer modified mortar which consists of cement, graded sand and special chemicals to increase water retention, bonding and strength. It is designed for smoothing surface concrete works including fully-bonded concrete slabs, precast panels, parapets, and any other concrete structures. It is can be used for repairing air bubble and concrete joint. Only water is required without cement addition.

Thin Coat Plaster Mortar #123 / 123 L is suitable for repairing minor surface defects on precast concrete or similar surfaces due to bubbles, demoulding, etc, can use single layer or multilayers..

Dry Mortar for Concrete Plastering No.120 / 120 S is suitable for plastering on concrete surfaces, including fully - bonded repairs to concrete slabs, path and steps.

Dry Plaster Mortar No.111 is suitable for plastering on light-weigth concrete/block. It is specially designed with high bond strength, delay set time, good water retention making plaster works finish faster and better quality.

Dry Plaster Mortar No.111 S is suitable for plastering on light-weigth concrete block. It is specially designed with high bond strength, delay set time, good water retention making plaster works finish faster and better quality. No.111 S can be applied by spray machine.

Dry Mortar for Plastering No.101 is suitable for plastering on brick and concrete block walls. No. 101 is standard grade used for general purpose with single coat and double coat and can be applied with plastering machine. The mortar contain dried and sieved aggregate of high quality, mixed with cement, binders, and additives in controlled proportion to give superior adhesion, workability and reduced shrinkage. This product was developed by specification and test methods covered by TIS Standard No. 1776-2542.

Dry Masonry Mortar NO. 250 is suitable for laying light – weight concrete / block. It is specially designed with high bond strength, delay set time, good water retention making laying concrete / block works easier, faster and better quality.

Dry Mortar for Masonry No. 125 is suitable for general masonry works. It can be used with brick or concrete blocks. No. 125 contain dried and sieved aggregate of high quality, mixed with cement, binders, and additives in controlled proportion to ensure good workability and adhesion making your work easy and durable. This product was developed by specification and test methods covered by TIS Standard No. 598-2547.